For further information please visit

Training Dual Certification WE and AWE 2011 Indonesia

Vibration During Welding At Power Plant (Steam Turbine)
PT. Semen Tonasa – Sulawesi Selatan

* Corrosion resistance
* Mechanical properties at elevated temperatures. KEYWORDS : Weld Metal Porosity, Embrittlement, Contamination Cracking, Vibration During Welding, Condensate, Tie Rod, Repair Welding, Conductivity. Introductions MATERIAL TYPES ALLOY GROUPINGS

  • Titanium; Commercially Pure (98-99,5 % Ti) or strengthned by small additions of oxygen, nitrogen, carbon and iron. The alloys are readily fusion weldable.
  • ALPHA ALLOYS : This are largely single phase alloys containing up to 7% alluminum and a small amount (<0.3%) of oxygen, nitrogen and carbon. The alloys are fusion welded in the annealed condition.
  • ALPHA-BETA ALLOYS : This have a characteristic two phase, microstructure formed by the addition of up 6% alluminium and varying amount of beta forming constituens - vadium, chromium and molybdenum. The alloys are readily welded in the annealed condition.

FILLER ALLOYS * Titanium and its alloys can be welded using a matching filler. Composition; Compositions are given in
* The American Welding Society Specification AWS A5.16-2004.


  • TIG and PLASMA processes, with argon or argon-helium shielding gas, are used for welding thin section components, typically <10 mm.
  • The most likely imperfections in fusion welds are :
    • - CONTAMINATION CRACKING (Hydrogen Cracking)


  • Porosity arises when gas bubbles are trapped between dendrites during solidification (in Titanium, Hydrogen from moisture in the arc environment or contamination on the filler and parent metal surface, is the most likely cause of porosity)
  • ACTION : Cleaned by Pickling (HF-HNO3), light grindingor Stainless Steel brushing in the join surface area.


  • Can be cause by weld metal contamination by either gas absorption or by dissolving contaminants such as dust (iron particles) on the surface. At temperatures above 500 deg. C, Titanium has a very high affinity for oxygen, nitrogen and hydrogen.
  • The weld pool, heat affected zone and cooling weld bead must be protected from oxidation by an inert gas / back up gas (Argon or Helium).
  • The color can indicate whether the shielding maximum. SILVER or STRAW color shows satisfactory gas shielding was achieved. DARK BLUE may be acceptable. Light blue, grey and white usually unacceptable (oxygen contamination).
  • For small components, an efficient gas shield can be achieved by welding in a totally enclosed chamber, fill with shielding gas. Oxygen level should be reduced to approximately 40 ppm before striking the arc on scrap titanium and <20 ppm before welding the actual component.
  • In tube welding, a fully enclosed head is equally effective in shielding the weld area and is preferable to orbital welding equipment in which the gas nozzle must be rotated around the tube.
  • When welding out in the open, the torch is fitted with a trailling shield to protect the hot weld bead while cooling.


CASE STUDY / WELDING REPAIR Power Plant at BTG Semen Tonasa - Pangkep Sulawesi Selatan is a coal steam turbine.
The condensate made from SS 410 with titanium lining (On tube sheet).
Join on Tube Sheet and Tie Rod is crack and sea water come inside to the boiler.
Problem..! So… we did repair welding on join tube sheet and tie rod.



  • If iron particles are present on the component surface, they dissolve in the weld metal reducing corrosion resistance and, at a sufficiently high iron content, causing embritlement. Iron particles are equally detrimental in the HAZ where local melting of the particles from pockets of titanium-iron eutectic. Micro cracking may occur but it is more likely that the iron-rich pockets will become preferential sites for corrosion.
  • Particular attention should be paid to separating titanium from steel fabrications, preferably by designating a specially reserved clean area. Welders should guard against embedding steel particles in to the surface of the material by :
    • - Avoiding steel fabrication operations near titanium components.
    • - Covering components to avoid airborne dust particles settling onthe surface.
    • - Not using tools, including wire brushes, previously used for steel.
    • - Scratch brushing the join area immediately before welding.
    • - Not handling the cleaned component with dirty gloves.
    • - To avoid corrosion cracking and minimize the risk of embritlement through iron contamination, it is best practice to fabricate titanium in a specially reserved clean area.



Titanium 6Al-4V AWS Class ER Ti-5


  • High strength to 600oF
  • Excellent general corrosion resistance
  • High strength-to-weight ratio


  • Gas turbine compressor dishes and blades
  • Airframe structural components (aircraft)
  • Chemical process equipment




Performance Profile

Ti 6Al-4V is the most widely used of all the alpha beta titanium alloys. Itmay be heat treated for high strength in welded construction at service temperatures through 600oF. Harden ability is limited and section over about one inch may not develop full properties. For cryogenic applications the extra low interstitial grade ELI (UNS R 56401) is preferred.

Annealing bar and forging is done at 1275-1325 oF 2hr air cool. Solution treat 1675-1725 oF 1hr water quench. Precipitation treat 975-1025 oF 3hr air cool. For increased fracture toughness but low tensile strength precipitation treat 1150 oF 4hr air cool.

Welding is by GTAW, direct current electrode negative, ¾ “ gas cup and gas lens. Limit electrode extension to 3/8 “. Inert gas shielding is required on all areas hotter than 800 oF. That is in addition to remarry torch shielding, trailing shield is required to protect the cooling weld metal, and back up shielding is required. Internal spaces should be purged 10 times the enclosed volume. Shield all tack welds.

Shielding and purge gas must be argon or argon helium mixture, NEVER nitrogen. Filler metal AWS A5.16 ERTi-5 may be used. ERTi-5 ELI preferred for greater toughness.



1.Sheet : Regular anneal furnace coolDuplex anneal. Mill anneal + 1435 oF, 15 minutes air cool. Triplex anneal. Mill anneal + 1850 oF, 5 minutes air cool, + 1375, 15 minutes air cool.

Bar and forgings :

Duplex anneal 1650-1850, 1 hour air cool + 1000oF -1100 oF, 8-24 hours air cool.

2.Bar duplex anneal : Mill anneal + 1000o – 1200oF, ½-6 hours air cool.

3.Anneal furnace cool at 300oF per hour maximum to 1000 oF to 1050 oF.

4.Stress relief may be accomplished at 800oF-15 hours, 850oF-5 hours, at 900oF-1 hour and 950 oF - ½ hour.

5.For 100% stress relief, 1000 oF -50 hours or 1200 oF -5 hours for 50% relief, 1000 oF -5 hours or 1100 oF – ½ hour.

6.Furnace cool at 300oF maximum from anneal temperature for maximum improved by holding at annealing temperature 24 hours.


7.Slow cool to 1000 o -1050 oF maximum from upper annealing temperature.

8.Anneal sheet at temperature for 20 minutes. For bar hold at anneal temperature 2 hours.




Tie Rod Titanium 6 Al 4 V


Tie rod titanium condensate is support at tube sheet with loaded sea water = 250m3/minute.




Prepare before welding (Turbine off)

    1. Clean up join tube sheet and tie rod, by light grinding (Blending) and Stainless Steel brush.
    2. Make V groove on crack at join tube sheet & tie rod.
    3. Welding Process :
      • Welding machine inverter ARCMART DC 16li.
      • Ampere 80A DC Negative.
      • Tungsten Thor 2% ø 1.6 mm with trailing torch.
      • Argon Gas, HP with out back up, flow 15 LPM
      • Filler AMS 4954/ER Ti-5 ø 1.6 mm
    4. Test : Penetrant Test (P.T)


After welding and cooling down, color on HAZ is looked silver (shielding gas maximum) Penetrant Test : accepted (No crack or porosity)



Turbine on, water conductivity at condensate and hot well 70. When broken! Water conductivity 900. (Sea water conductivity 64,000).

Recommended for boiler <10, during operation before crack on join tube sheet & tie rod=8, After first repair conductivity 70…. Not accepted. After 2x24 hours… conductivity up to 4,000 and than shut down the turbine…!!



SECOND PREPAIRE (Turbine … Start Up)

1.Re-cleaned up on tube sheet & tie rod.

2.Re-make V groove on tube sheet & tie rod.

3.Re-welding process:

  • a.Welding machine inverter ARCMART DC 161i.
  • b.Ampere 80A DC Negative.
  • c.Tungsten Thor 2% ø 1.6 mm with out trailing / with gas lens.
  • d.Argon Gas HP with out back up with flow 20 LPM.
  • e. Filler AMS 4954 / ER Ti-5ø 1.6 mm.




84 Bar vacuum test with water soap… No broken (accepted)


On HAZ color… SILVER.

Penetrant test… No Crack or porosity.


After 2x24 hours… Turbine running, conductivity=2.4…very good

Electric power connect to transmission.


Root pass… RPM 1000 ( Start up)

Filling …… RPM 2000 ( Start up)

Capping …. RPM 3000 (Running)


Clean , clean and clean …is very important

Shield, shield and shield …is very important

Vibration During Welding is a way to the good welding of Titanium


  • Welding hand book Metals and Their Weld ability Section Four Sixth Edition American Welding Society 1972 chapter 73.
  • More than 20 years experienced in welding.


The Japan International Welding Show 2012 (organized by the Japan Welding Engineering Society and Sanpo Publications Inc.) will take place at Intex Osaka, in Suminoe-ku, Osaka, for four days from April 11 to 14, 2012.

Extending the theme of the previous year’s Tokyo event, the show will also feature a “Welding Promenade” to foster exchanges between the Asian countries, as well as to facilitate the exchange of information. The principal objectives of the Welding Promenade are to help establish a single, common welding market in Asia, and to create business networks between Japan and other Asian countries. This will be accomplished by providing Asian visitors opportunities to learn about Japanese technology, promoting the exchange of information between visitors from various countries, and fostering closer relationships with International Welding Show exhibitors.

This year’s show is expected to have a particularly strong international flavor because it will be held concurrently with both the Asian Welding Federation (AWF) general and task force meetings, and also due to the large number of exhibiting companies from all over Asia. These factors are expected to play major roles in the creation of a large, common welding market in Asia, which is what Welding Promenade is all about.

This first Welding Promenade was held during the Japan International Welding Show 2010, in Tokyo. In that event, Sanpo Publications brought together a large number of Asian nation dealers and users to help them develop networks among each other while concurrently forming relationship with Japanese manufacturers. This event allowed all parties to get to know each other better, explore needs and offerings, exchange information, and provide products that are appropriate to the particular needs of their respective countries. In addition, to help in establishing technical information service networks, the Welding Promenade also provided a forum for the creation of partnership between Asian countries through its various exhibitions, seminars, and the business matching facility.

Internationally, the welding industry of today is experiencing lively technological development in response to vigorous investment in plants and equipment. In Asian countries, in particular, there is rapid and ongoing progress towards the formation of regional welding markets. To continue enlivening Asian welding industries, it is important to promote greater exchanges of welding technologies, strengthen interpersonal exchanges between persons from various countries, and facilitate exchanges between the relevant industrial bodies of each country. This will allow us to unlock new potentials and explore new ways of addressing the needs of welding-related products and services in Asia.

Looking to the future, if the welding market in Asia becomes more solid and stable, we can expect to see the institution of various cooperation scheme at national levels aimed at nurturing welding industries. These could include the conclusion of cooperation agreements between countries that focus on business matters, as well as research and development.

The AWF was formally established in 2004 when industry representative bodies from various Asian countries met in Philippines. The aim og the federation is the development of Asia’s welding industry. The primary goals of the AWD, as they were stated at the time, were to establish and disseminate a unified personnel certification scheme across Asia for welders, welding engineers, and welding inspectors, as well as to establish a personnel utilization system.

In addition, there were calls for Japan to share technical information, technology, skills, and education and training systems more widely with other countries in Asia, and to provide welding-related companies in the region with assistance, solidarity, and cooperation.

Linking the countries of Asia through welding technology requires the construction of networks that enable countries to exchange information that helps them understand each other’s welding-related needs, as well as the state and conditions of welding industries in their countries. This was the concept behind the launching of Welding Promenade.

As a first step forward linking Japan and other Asia countries through welding technology, it is essential to exchange information, and thus develop business networks, that enable each country to understand each other country’s needs. And this, precisely, is the role of the Welding Promenade at the Japan International Welding Show.

The show is expected to attract dealers and users from around Asia, who view the Welding Promenade as a tool for building their business networks. By utilizing the opportunity to exchange information with manufactures at the show, welding and cutting industry-related users and dealers from all over Asia can be expected to gain improved mutual understandings of each others “seeds and needs”, exchange and offer products and technical information appropriate to the particular needs of their countries, and to build enhanced service networks.

As describe above, Sanpo Publications has commenced registration for exhibitors and those who wish to participate in its “business matching (Visit Scheduler)” service, which is a key feature of the Welding Promenade concept. All exhibiting companies and show visitors are invited to register for the service. As Welding Promenade participants, all those who register will be invited to the welcome reception on the evening of the first day of the event. Based on our focus of creating a single, common market from the Asian welding industry, we look forward to your participation.


Member Countries



Only registered countries above have access to our member pages.

AWF Calendar

June 2022
Mo Tu We Th Fr Sa Su
30 31 1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
20 21 22 23 24 25 26
27 28 29 30 1 2 3
Afrikaans Chinese simplified English German Indonesian Japanese Malay